U-seals, Polypaks, U-cups

Style 850 u-seals offer excellent resistance to extrusion and abrasion. The round cross-section expander offers energized sealing from zero to 5,000 psi.

95A Durometer | Urethane Material | 2 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal

Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder. Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.

The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.

94A Durometer | Urethane Material | 1 3/8 in Nominal Inner Diameter | 1/8 in Cross Section | U-Seal

Features

• General purpose rod seal
• Robust design
• Excellent wear resistance
• Increase seal stability
• Performs well over wide temperature range and is extremely effective in low temperatures
• Primary lip protection
• Easy to install

Style HRU u-seals are precision molded from 80 Durometer Buna-N rubber. Sizes include those found in Army-Navy spec. AN6226 and narrow cross-section sizes found in J.I.C. cylinders and the popularly termed “Huva Cup”.

80A Durometer | Buna-N Rubber Material | 2 1/8 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal

Specifically designed as piston seals, these u-seals are engineered to seal on their outside diameter. They offer extended, service life and maximum reliability in piston sealing.

92A Durometer | Urethane Material | 3 1/2 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal

Molded in a tough urethane, this rod u-seal fits tightly in the groove while providing increased radial force on the rod.

Urethane Material | 50 MM Nominal Inner Diameter | Rod U-Seal

Style 850 u-seals offer excellent resistance to extrusion and abrasion. The round cross-section expander offers energized sealing from zero to 5,000 psi.

95A Durometer | Urethane Material | 1 1/4 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal

Style 850 u-seals offer excellent resistance to extrusion and abrasion. The round cross-section expander offers energized sealing from zero to 5,000 psi.

95A Durometer | Urethane Material | 6 1/2 in Nominal Inner Diameter | 7/32 in Cross Section | U-Seal

Molded in a tough urethane, this rod u-seal fits tightly in the groove while providing increased radial force on the rod.

Urethane Material | 45 MM Nominal Inner Diameter | Rod U-Seal

Molded in a tough urethane, this seal employs an additional lip near the heel. The twin lip design provides stability, friction-reducing lube retention, and some contaminant resistance. VME – Secondary lip is further from heel than standard MRTU. NOTE: E = European Urethane.

Urethane Material | 35 MM Nominal Inner Diameter | Rod U-Seal

Features

• Excellent low temperature performance
• Easy installation

Style 850 u-seals offer excellent resistance to extrusion and abrasion. The round cross-section expander offers energized sealing from zero to 5,000 psi.

95A Durometer | Urethane Material | 2 1/8 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal