Backup Rings
Search in Category
Filter Your Search
Shop by Category
Solid Teflon backup ring with a flat cross-section.
PTFE can withstand high temperatures and is compatible with nearly all fluids.
PTFE Material | 1 5/8 in Nominal Inner Diameter | 3/16 in Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
- Deals very well with surface wear
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 6 1/4 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 6 1/2 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 8 3/4 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 2 7/8 in Nominal Inner Diameter | 3/16 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 3 1/2 in Nominal Inner Diameter | 3/16 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Solid Urethane backup ring with a flat cross-section.
95A Durometer | Urethane Material | 2 1/8 in Nominal Inner Diameter | 3/32 in Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
Solid Teflon backup ring with a flat cross-section.
PTFE can withstand high temperatures and is compatible with nearly all fluids.
- High temperature range
- Deals very well with surface wear
8 X 8 1/2 Back-up SOLID PTFE
Commonly used with metric o-rings, these back-up rings are made of virgin PTFE unless suffix specifies otherwise.
PTFE Material | 44 MM Nominal Inner Diameter | 3 MM Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation