Backup Rings
Search in Category
Filter Your Search
Shop by Category
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 3 1/8 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Solid Teflon backup ring with a flat cross-section.
PTFE can withstand high temperatures and is compatible with nearly all fluids.
PTFE Material | 1 1/4 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
- Deals very well with surface wear
Solid Urethane backup ring with a flat cross-section.
95A Durometer | Urethane Material | 1 1/2 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
Style 590 Back-up Rings feature exceptional strength and abrasion resistance along with a 53 Shore D hardness rating which makes them suitable for high pressure service where extrusion is a problem. Primarily used as a u-seal back-up, these rings can be used with o-rings. They also retrofit urethane and PTFE back-up rings, with greater performance characteristics. “S” suffix designates a split ring.
53 Shore D Durometer | Hytrel Material | 4 in Nominal Inner Diameter | 1/4 in Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
Commonly used with metric o-rings, these back-up rings are made of virgin PTFE unless suffix specifies otherwise.
PTFE Material | 95 MM Nominal Inner Diameter | 2.5 MM Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 1 5/8 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 1 7/8 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Solid Urethane backup ring with a flat cross-section.
95A Durometer | Urethane Material | 4 1/4 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
Solid Teflon backup ring with a flat cross-section.
PTFE can withstand high temperatures and is compatible with nearly all fluids.
PTFE Material | 8 1/2 in Nominal Inner Diameter | 1/4 in Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
- Deals very well with surface wear
Style 590 Back-up Rings feature exceptional strength and abrasion resistance along with a 53 Shore D hardness rating which makes them suitable for high pressure service where extrusion is a problem. Primarily used as a u-seal back-up, these rings can be used with o-rings. They also retrofit urethane and PTFE back-up rings, with greater performance characteristics. “S” suffix designates a split ring.
53 Shore D Durometer | Hytrel Material | 1 3/8 in Nominal Inner Diameter | 5/32 in Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation